2 tiers with a towel rail. Measures 21 1/2 x 18 1/2" Pick up Erin
Wall mirror. Needs tiny touch up on one corner.(See photo)Solid piece. Pick up Erin.
These are the Ford OEM exhaust manifolds for the 390GT or 428 police interceptor cylinder heads. They are in decent condition.
Ford RUG-3 toploader out of a 69 Mustang. I was going to drop it into my 68 Mustang but decided on a Cleveland instead. Internals all look good and it shifts fine. Should not need rebuilding unless you're a perfectionist.
This Ford HEH-D Toploader came out of a 1964, 390 Galaxy 500. It is an early toploader that has the square faceplate as opposed to the butterfly shape.The internals all look good and it shifts easily.
This is a 3-speed manual transmission w/overdrive. It looks just like a Ford Toploader 4-speed except the speedometer cable hooks to the opposite side. The shifter is the correct one for it and shows the 3-speed pattern with overdrive on the shifter knob.
This is a used 28 spline, open carrier differential for a Ford 9-inch rear.
I have two Ford small block C-6 automatic transmissions & two for big blocks.
I have 3 engine blocks; a 2-bolt main shortblock a 2-bolt main bare block, and a 4-bolt main bare block; a single 4V bare head with hardened valve seats installed; 2 complete sets of rocker arms; new set of Badger. 030 pistons, set of .040 pistons and rods, set of connecting rods, set of standard pistons and rods; d3ze-9425-AA-X spreadbore intake for 4V heads; 2 bbl intake; four crankshafts; ha...
I have a rebuilt 390 and a 390 short block; a pair of C8AE-H 390GT or 428 police interceptor cylinder heads with the 16 holes on the exhaust side for $275.00 and the high performance exhaust manifolds for them at $250.00; oil pans; valve covers; etc.
Have many spare parts, mostly used, including fenders, a few new repair panels, windshields, window glass, taillights & bezels, voltage regulators, bearings, distributors, interior kick panels, steering columns and wheels, grille & mustangs w/corrals, instrument cluster, etc.
I have two C-6 trannies that fit the Ford small-block engine and I have two that will fit big blocks.
I have a set of cylinder heads for $150.00, a flywheel for $50.00, a set of long headers for $75.00, a set of cast iron exhaust manifolds for $40.00, and a new set of plug wires for $15.00.
I have four Holley #4160, 600 CFM four-bbl. carburetors at $50 each; three Ford Motorcraft/Autolite spreadbore carbs. at $50.00 each; a 2 bbl. and an old Holley #4360, 450 CFM 4 bbl. carb. for $35.00 each.
In excellent condition. Upper: 52% Cotton, 40% viscose, 8% Nylon Lower: 58% Cotton and 42% Viscose Brand is OshKosh B Gosh Cross posted.
This is a nice heavy elliptical machine. Everything works well except the fan. But to be honest it didn t ever do that much anyway! There are a few places where it came into contact against a white door (when we moved it out) and then a scratch/dent thing. Please see additional pics. FCFS
Excellent condition. 100% Cotton. Brand is OshKosh. Cross posted.
Very good used condition. 100% Cotton. Cross posted.
This fridge is in good shape overall and has been being used as an extra one in the garage. It s around 6 years old. There is a couple of small dents on the right side about a third of the way up from the bottom. The big one is approximately 2 inches. See additional pics. Need gone ASAP! FCFS
The sleeves zip on and off so it can turn into a vest. In excellent condition. Brand is Little Miss Attitude. 100% Polyester. Cross posted.